Podręcznik użytkownika

Copyright © 2019. Ten dokument jest chroniony prawem autorskim. Lista autorów znajduje się poniżej. Możesz go rozpowszechniać oraz modyfikować na zasadach określonych w GNU General Public License (http://www.gnu.org/licenses/gpl.html), wersja 3 lub późniejsza, albo określonych w Creative Commons Attribution License (http://creativecommons.org/licenses/by/3.0/), wersja 3.0 lub późniejsza.

Współtwórcy

Heitor de Bittencourt. Mathias Neumann

Tłumaczenie

Kerusey Karyu <[email protected]>, 2014-2019.

Kontakt

Wszelkie zauważone błędy, sugestie lub nowe wersje dotyczące tego dokumentu prosimy kierować do:

Data publikacji i wersja oprogramowania

March 05 2020

Wprowadzenie

The KiCad PCB Calculator is a set of utilities to help you find the values of components or other parameters of a layout. The Calculator has the following tools:

  • Regulatory napięć

  • Szerokości ścieżek

  • Prześwit

  • Linia transmisyjna

  • Tłumiki RF

  • Kolory kodów

  • Klasy płytek

Regulatory napięć

Regulatory napięć

Ten panel kalkulatora pozwala dobrać wartości rezystorów potrzebnych w układach liniowych regulatorów napięć (klasycznych lub LDO) do ustalenia napięcia wyjściowego takiego regulatora.

Regulatory napięć

For the Standard Type, the output voltage Vout as a function of the reference voltage Vref and resistors R1 and R2 is given by:

Regulatory napięć

For the 3 terminal type, there is a correction factor due to the quiescent current Iadj flowing from the adjust pin:

Regulatory napięć

Ten prąd zwykle nie przekracza 100uA i może zostać pominięty, ale z zachowaniem pewnych środków ostrożności.

To use this calculator, enter the parameters of the regulator Type, Vref and, if needed, Iadj, select the field you want to calculate (one of the resistors or the output voltage) and enter the other two values.

Szerokości ścieżek

The Track Width tool calculates the trace width for printed circuit board conductors for a given current and temperature rise. It uses formulas from IPC-2221 (formerly IPC-D-275).

Szerokości ścieżek

Prześwit

This table helps finding the minimum clearance between conductors.

Each line of the table has a minimum recomended distance between conductors for a given voltage (DC or AC peaks) range. If you need the values for voltages higher than 500V, enter the value in the box in the left corner and press Update Values.

Prześwit

Linie transmisyjne

Teoria linii transmisyjnych jest kamieniem węgielnym w nauczaniu zjawisk radiowych i inżynierii mikrofalowej.

In the calculator you can choose different sorts of Line Types and their special parameters. The models implemented are frequency-dependent, so they disagree with simpler models at high enough frequencies.

This calculator is heavilly based on Transcalc.

The transmission line types and the reference of their mathematical models are listed below:

  • Microstrip line:

    • H. A. Atwater, “Simplified Design Equations for Microstrip Line Parameters”, Microwave Journal, pp. 109-115, November 1989.

  • Coplanar wave guide.

  • Coplanar wave guide with ground plane.

  • Rectangular waveguide:

    • S. Ramo, J. R. Whinnery and T. van Duzer, "Fields and Waves in Communication Electronics", Wiley-India, 2008, ISBN: 9788126515257.

  • Coaxial line.

  • Coupled microstrip line:

    • H. A. Atwater, “Simplified Design Equations for Microstrip Line Parameters”, Microwave Journal, pp. 109-115, November 1989.

    • M. Kirschning and R. H. Jansen, "Accurate Wide-Range Design Equations for the Frequency-Dependent Characteristic of Parallel Coupled Microstrip Lines," in IEEE Transactions on Microwave Theory and Techniques, vol. 32, no. 1, pp. 83-90, Jan. 1984. doi: 10.1109/TMTT.1984.1132616.

    • Rolf Jansen, "High-Speed Computation of Single and Coupled Microstrip Parameters Including Dispersion, High-Order Modes, Loss and Finite Strip Thickness", IEEE Trans. MTT, vol. 26, no. 2, pp. 75-82, Feb. 1978.

    • S. March, "Microstrip Packaging: Watch the Last Step", Microwaves, vol. 20, no. 13, pp. 83.94, Dec. 1981.

  • Stripline.

  • Twisted pair.

Linie transmisyjne

Tłumiki RF

With the RF Attenuator utility you can calculate the values of the resistors needed for different types of attenuators:

  • Typu Pi

  • Typu T

  • Mostkowy typu T

  • Splitter rezystorowy

To use this tool, first select the type of attenuator you need, then enter the desired attenuation (in dB) and input/output impedances (in Ohms).

Tłumiki RF

Kolory kodów

Ten panel jest pomocny przy ustalaniu wartości rezystancji rezystorów które zostały opisane kolorowymi paskami. Używając go należy najpierw określić tolerancję danego rezystora: 10%, 5% lub równą lub mniejszą niż 2%. Na przykład:

  • Yellow Violet Red Gold: 4 7 x100 ±5% = 4700 Ohm, 5% tolerance

  • 1kOhm, 1% tolerance: Brown Black Black Brown Brown

Kolory kodów

Klasy płytek

Performance Classes

In IPC-6011 have been three performance classes established

  • Class 1 General Electronic Products Includes consumer products, some computer and computer peripherals suitable for applications where cosmetic imperfections are not important and the major requirement is function of the completed printed board.

  • Class 2 Dedicated Service Electronic Products Includes communications equipment, sophisticated business machines, instruments where high performance and extended life is required and for which uninterrupted service is desired but not critical. Certain cosmetic imperfections are allowed.

  • Class 3 High Reliability Electronic Products Includes the equipment and products where continued performance or performance on demand is critical. Equipment downtime cannot be tolerated and must function when required suchas in life support items or flight control systems. Printed boards in this class are suitable for applications where high levels of assurance are required and service is essential.

PCB Types

In IPC-6012B there are also 6 Types of PCB defined:

  • Printed Boards without plated through holes (1)

    • 1 Single-Sided Board

  • And Boards with plated through holes (2-6)

    • 2 Double-Sided Board

    • 3 Multilayer board without blind or buried vias

    • 4 Multilayer board with blind and/or buried vias

    • 5 Multilayer metal core board without blind orburied vias

    • 6 Multilayer metal core board with blind and/orburied vias

Klasy płytek