Essential and concise guide to mastering KiCad for the successful development of sophisticated electronic printed circuit boards.

This document is Copyright © 2010-2015 by its contributors as listed below. You may distribute it and/or modify it under the terms of either the GNU General Public License (http://www.gnu.org/licenses/gpl.html), version 3 or later, or the Creative Commons Attribution License (http://creativecommons.org/licenses/by/3.0/), version 3.0 or later.

All trademarks within this guide belong to their legitimate owners.

Contributors

David Jahshan, Phil Hutchinson, Fabrizio Tappero, Christina Jarron, Melroy van den Berg.

translation

Melroy van den Berg <[email protected]>, 2015.

Feedback

Please direct any bug reports, suggestions or new versions to here:

Publication date

2015, May 16.

Introduction to KiCad

KiCad is an open-source software tool for the creation of electronic schematic diagrams and PCB artwork. Beneath its singular surface, KiCad incorporates an elegant ensemble of the following stand-alone software tools:

Program name Description File extension

KiCad

Project manager

*.pro

Eeschema

Schematic editor (both schematic and component)

*.sch, *.lib, *.net

CvPcb

Footprint selector

*.net

Pcbnew

Circuit board board editor

*.kicad_pcb

GerbView

Gerber viewer

All the usual gerbers

Bitmap2Component

Convert bitmap images to components or footprints

*.lib, *.kicad_mod, *.kicad_wks

PCB Calculator

Calculator for components, track width, electrical spacing, color codes, and more…​

None

Pl Editor

Page layout editor

*.kicad_wks

The file extension list is not complete and only contains a subset of the files that KiCad works with that is useful for the basic understanding of which files are used for each KiCad unique application.

KiCad can be considered mature enough to be used for the successful development and maintenance of complex electronic boards.

KiCad does not present any board-size limitation and it can easily handle up to 32 copper layers, up to 14 technical layers and up to 4 auxiliary layers. KiCad can create all the files necessary for building printed boards, Gerber files for photo-plotters, drilling files, component location files and a lot more.

Being open source (GPL licensed), KiCad represents the ideal tool for projects oriented towards the creation of electronic hardware with an open-source flavour.

On the Internet, the home of KiCad is:

Download and install KiCad

KiCad runs on GNU/Linux, Apple OS X and Windows. You can find the most up to date instructions and download links at:

KiCad stable releases occur periodically per the KiCad Stable Release Policy. New features are continually being added to the development branch. If you would like to take advantage of these new features and help out by testing them, please download the latest nightly build package for your platform. Nightly builds may introduce bugs but it is the goal of the KiCad Development Team to keep the development branch as usable as possible during new feature development.

Under GNU/Linux

Stable builds

Stable releases of KiCad can be found in most distribution’s package managers as kicad and kicad-doc. If your distribution does not provide latest stable version, please follow the instruction for unstable builds and select and install the latest stable version.

Unstable (nightly development) builds

Unstable builds are built from the most recent source code. They can sometimes have bugs that cause file corruption, generate bad gerbers, etc, but are generally stable and have the latest features.

Under Ubuntu, the easiest way to install an unstable nightly build of KiCad is via PPA and Aptitude. Type the following into your Terminal:

sudo add-apt-repository ppa:js-reynaud/ppa-kicad

sudo aptitude update && sudo aptitude safe-upgrade

sudo aptitude install kicad kicad-doc-en

Under Fedora the easiest way to install an unstable nightly build is via copr. To install KiCad via copr type the following in to copr:

sudo dnf copr enable mangelajo/kicad

sudo dnf install kicad

Alternatively, you can download and install a pre-compiled version of KiCad, or directly download the source code, compile and install KiCad.

Under Apple OS X

Stable builds

Stable builds of KiCad for OS X can be found at: https://downloads.kicad.org/kicad/macos/explore/stable

Unstable (nightly development) builds

Unstable builds are built from the most recent source code. They can sometimes have bugs that cause file corruption, generate bad gerbers, etc, but are generally stable and have the latest features.

Unstable nightly development builds can be found at: https://downloads.kicad.org/kicad/macos/explore/nightlies

Under Windows

Stable builds

Stable builds of KiCad for Windows can be found at: https://downloads.kicad.org/kicad/windows/explore/stable

Unstable (nightly development) builds

Unstable builds are built from the most recent source code. They can sometimes have bugs that cause file corruption, generate bad gerbers, etc, but are generally stable and have the latest features.

For Windows you can find nightly development builds at: https://downloads.kicad.org/kicad/windows/explore/nightlies

Support

If you have ideas, remarks or questions, or if you just need help:

KiCad Workflow

Despite its similarities with other PCB software tools, KiCad is characterised by an interesting work-flow in which schematic components and footprints are actually two separate entities. This is often the subject of discussion on Internet forums.

KiCad Workflow overview

The KiCad work-flow is comprised of two main tasks: making the schematic and laying out the board. Both a component library and a footprint library are necessary for these two tasks. KiCad has plenty of both. Just in case that is not enough, KiCad also has the tools necessary to make new ones.

In the picture below, you see a flowchart representing the KiCad work-flow. The picture explains which steps you need to take, in which order. When applicable, the icon is added as well for convenience.

KiCad Flowchart

For more information about creating a component, see the section of this document titled Make schematic components in KiCad. And for more information about how to create a new footprint, see the section of this document titled Make component footprints.

On the following site:

You will find an example of use of a tool that allows you to quickly create KiCad library components. For more information about quicklib, refer to the section of this document titled Make Schematic Components With quicklib.

Forward and backward annotation

Once an electronic schematic has been fully drawn, the next step is to transfer it to a PCB following the KiCad work-flow. Once the board layout process has been partially or completely done, additional components or nets might need to be added, parts moved around and much more. This can be done in two ways: Backward Annotation and Forward Annotation.

Backward Annotation is the process of sending a PCB layout change back to its corresponding schematic. Some do not consider this particular feature especially useful.

Forward Annotation is the process of sending schematic changes to a corresponding PCB layout. This is a fundamental feature because you do not really want to re-do the layout of the whole PCB every time you make a modification to your schematic. Forward Annotation is discussed in the section titled Forward Annotation.

Draw electronic schematics

In this section we are going to learn how to draw an electronic schematic using KiCad.

Using Eeschema

  1. Under Windows run kicad.exe. Under Linux type 'kicad' in your Terminal. You are now in the main window of the KiCad project manager. From here you have access to eight stand-alone software tools: Eeschema, Schematic Library Editor, Pcbnew, PCB Footprint Editor, GerbView, Bitmap2Component, PCB Calculator and Pl Editor. Refer to the work-flow chart to give you an idea how the main tools are used.

    KiCad Main Window
  2. Create a new project: FileNew ProjectNew Project. Name the project file 'tutorial1'. The project file will automatically take the extension ".pro". KiCad prompts to create a dedicated directory, click "Yes" to confirm. All your project files will be saved here.

  3. Let’s begin by creating a schematic. Start the schematic editor Eeschema, Eeschema. It is the first button from the left.

  4. Click on the 'Page Settings' icon Sheet settings icon on the top toolbar. Set the Page Size as 'A4' and enter the Title as 'Tutorial 1'. You will see that more information can be entered here if necessary. Click OK. This information will populate the schematic sheet at the bottom right corner. Use the mouse wheel to zoom in. Save the whole schematic project: FileSave Schematic Project

  5. We will now place our first component. Click on the 'Place component' icon Add component Icon in the right toolbar. The same functionality is achieved by pressing the 'Place component' shortcut key ('a').

    You can see a list of all available shortcut keys by pressing the '?' key.
  6. Click on the middle of your schematic sheet. A Choose Component window will appear on the screen. We’re going to place a resistor. Search / filter on the 'R' of Resistor. You may notice the 'device' heading above the Resistor. This 'device' heading is the name of the library where the component is located, which is quite a generic and useful library.

    Choose Component
  7. Double click on it. This will close the 'Choose Component' window. Place the component in the schematic sheet by clicking where you want it to be.

  8. Click on the magnifier icon to zoom in on the component. Alternatively, use the mouse wheel to zoom in and zoom out. Press the wheel (central) mouse button to pan horizontally and vertically.

  9. Try to hover the mouse over the component 'R' and press the r key. The component should rotate. You do not need to actually click on the component to rotate it.

    If your mouse was also over the Field Reference ('R') or the Field Value ('R?'), a menu will appear. You will see these 'Clarify Selection' menu often in KiCad, they allow working on objects that are on top of each other. In this case, tell KiCad you want to perform the action on the 'Component …​R…​'.
  10. Right click in the middle of the component and select Edit ComponentValue. You can achieve the same result by hovering over the component and pressing the v key. Alternatively, the e key will take you to the more general Edit window. Notice how the right-click menu below shows shortcut keys for all available actions.

    Edit component menu
  11. The Component value window will appear. Replace the current value 'R' with '1 k'. Click OK.

    Do not change the Reference field (R?), this will be done automatically later on. The value inside the resistor should now be '1 k'.
    Resistor Value
  12. To place another resistor, simply click where you want the resistor to appear. The Component Selection window will appear again.

  13. The resistor you previously chose is now in your history list, appearing as 'R'. Click OK and place the component.

    Component history
  14. In case you make a mistake and want to delete a component, right click on the component and click 'Delete Component'. This will remove the component from the schematic. Alternatively, you can hover over the component you want to delete and press the del key.

    You can edit any default shortcut key by going to PreferencesHotkeysEdit hotkeys. Any modification will be saved immediately.
  15. You can also duplicate a component already on your schematic sheet by hovering over it and pressing the c key. Click where you want to place the new duplicated component.

  16. Right click on the second resistor. Select 'Drag Component'. Reposition the component and left click to drop. The same functionality can be achieved by hovering over the component and by pressing the g key. Use the r key to rotate the component. The x key and the y key will flip the component.

    Right-ClickMove component (equivalent to the m key option) is also a valuable option for moving anything around, but it is better to use this only for component labels and components yet to be connected. We will see later on why this is the case.
  17. Edit the second resistor by hovering over it and pressing the v key. Replace 'R' with '100'. You can undo any of your editing actions with the ctrl+z key.

  18. Change the grid size. You have probably noticed that on the schematic sheet all components are snapped onto a large pitch grid. You can easily change the size of the grid by Right-ClickGrid select. In general, it is recommended to use a grid of 50.0 mils for the schematic sheet.

  19. We are going to add a component from a library that isn’t configured in the default project. In the menu, choose PreferencesComponent Libraries and click the Add button for Component library files.

  20. You need to find where the official KiCad libraries are installed on your computer. Look for a library directory containing a hundred of .dcm and .lib files. Try in C:\Program Files (x86)\KiCad\share\ (Windows) and /usr/share/kicad/library/ (Linux). When you have found the directory, choose and add the 'microchip_pic12mcu' library and close the window.

  21. Repeat the add-component steps, however this time select the 'microchip_pic12mcu' library instead of the 'device' library and pick the 'PIC12C508A-I/SN' component.

  22. Hover the mouse over the microcontroller component. Press the y key or the x key on the keyboard. Notice how the component is flipped over its x axis or its y axis. Press the key again to return it to its original orientation.

  23. Repeat the add-component steps, this time choosing the 'device' library and picking the 'LED' component from it.

  24. Organise all components on your schematic sheet as shown below.

    gsik_tutorial1_010_png
  25. We now need to create the schematic component 'MYCONN3' for our 3-pin connector. You can jump to the section titled Make Schematic Components in KiCad to learn how to make this component from scratch and then return to this section to continue with the board.

  26. You can now place the freshly made component. Press the 'a' key and pick the 'MYCONN3' component in the 'myLib' library.

  27. The component identifier 'J?' will appear under the 'MYCONN3' label. If you want to change its position, right click on 'J?' and click on 'Move Field' (equivalent to the m key option). It might be helpful to zoom in before/while doing this. Reposition 'J?' under the component as shown below. Labels can be moved around as many times as you please.

    gsik_myconn3_s_png
  28. It is time to place the power and ground symbols. Click on the 'Place a power port' button add_power_png on the right toolbar. Alternatively, press the 'p' key. In the component selection window, scroll down and select 'VCC' from the 'power' library. Click OK.

  29. Click above the pin of the 1 k resistor to place the VCC part. Click on the area above the microcontroller 'VDD'. In the 'Component Selection history' section select 'VCC' and place it next to the VDD pin. Repeat the add process again and place a VCC part above the VCC pin of 'MYCONN3'.

  30. Repeat the add-pin steps but this time select the GND part. Place a GND part under the GND pin of 'MYCONN3'. Place another GND symbol on the right of the VSS pin of the microcontroller. Your schematic should now look something like this:

    gsik_tutorial1_020_png
  31. Next, we will wire all our components. Click on the 'Place wire' icon Place wire on the right toolbar.

    Be careful not to pick 'Place a bus', which appears directly beneath this button but has thicker lines. The section Bus Connections in KiCad will explain how to use a bus section.
  32. Click on the little circle at the end of pin 7 of the microcontroller and then click on the little circle on pin 2 of the LED. You can zoom in while you are placing the connection.

    If you want to reposition wired components, it is important to use the g key (grab) option and not the m key (move) option. Using the grab option will keep the wires connected. Review step 24 in case you have forgotten how to move a component.
    gsik_tutorial1_030_png
  33. Repeat this process and wire up all the other components as shown below. To terminate a wire just double-click. When wiring up the VCC and GND symbols, the wire should touch the bottom of the VCC symbol and the middle top of the GND symbol. See the screenshot below.

    gsik_tutorial1_040_png
  34. We will now consider an alternative way of making a connection using labels. Pick a net labelling tool by clicking on the 'Place net name' icon add_line_label_png on the right toolbar. You can also use the l key.

  35. Click in the middle of the wire connected to pin 6 of the microcontroller. Name this label 'INPUT'.

  36. Follow the same procedure and place another label on line on the right of the 100 ohm resistor. Also name it 'INPUT'. The two labels, having the same name, create an invisible connection between pin 6 of the PIC and the 100 ohm resistor. This is a useful technique when connecting wires in a complex design where drawing the lines would make the whole schematic messier. To place a label you do not necessarily need a wire, you can simply attach the label to a pin.

  37. Labels can also be used to simply label wires for informative purposes. Place a label on pin 7 of the PIC. Enter the name 'uCtoLED'. Name the wire between the resistor and the LED as 'LEDtoR'. Name the wire between 'MYCONN3' and the resistor as 'INPUTtoR'.

  38. You do not have to label the VCC and GND lines because the labels are implied from the power objects they are connected to.

  39. Below you can see what the final result should look like.

    gsik_tutorial1_050_png
  40. Let’s now deal with unconnected wires. Any pin or wire that is not connected will generate a warning when checked by KiCad. To avoid these warnings you can either instruct the program that the unconnected wires are deliberate or manually flag each unconnected wire or pin as unconnected.

  41. Click on the 'Place no connect flag' icon noconn_png on the right toolbar. Click on pins 2, 3, 4 and 5. An X will appear to signify that the lack of a wire connection is intentional.

    gsik_tutorial1_060_png
  42. Some components have power pins that are invisible. You can make them visible by clicking on the 'Show hidden pins' icon hidden_pin_png on the left toolbar. Hidden power pins get automatically connected if VCC and GND naming is respected. Generally speaking, you should try not to make hidden power pins.

  43. It is now necessary to add a 'Power Flag' to indicate to KiCad that power comes in from somewhere. Press the a key, select 'List All', double click on the 'power' library and search for 'PWR_FLAG'. Place two of them. Connect them to a GND pin and to VCC as shown below.

    gsik_tutorial1_070_png
    This will avoid the classic schematic checking warning: Warning Pin power_in not driven (Net xx)
  44. Sometimes it is good to write comments here and there. To add comments on the schematic use the 'Place graphic text (comment)' icon add_text_png on the right toolbar.

  45. All components now need to have unique identifiers. In fact, many of our components are still named 'R?' or 'J?'. Identifier assignation can be done automatically by clicking on the 'Annotate schematic' icon annotate_png on the top toolbar.

  46. In the Annotate Schematic window, select 'Use the entire schematic' and click on the 'Annotation' button. Click OK in the confirmation message and then click 'Close'. Notice how all the '?' have been replaced with numbers. Each identifier is now unique. In our example, they have been named 'R1', 'R2', 'U1', 'D1' and 'J1'.

  47. We will now check our schematic for errors. Click on the 'Perform electrical rules check' icon erc_png on the top toolbar. Click on the 'Run' button. A report informing you of any errors or warnings such as disconnected wires is generated. You should have 0 Errors and 0 Warnings. In case of errors or warnings, a small green arrow will appear on the schematic in the position where the error or the warning is located. Check 'Create ERC file report' and press the 'Run' button again to receive more information about the errors.

    If you have a warning with "No default editor found you must choose it", try setting the path to c:\windows\notepad.exe (windows) or /usr/bin/gedit (Linux).
  48. The schematic is now finished. We can now create a Netlist file to which we will add the footprint of each component. Click on the 'Generate netlist' icon netlist_png on the top toolbar. Click on the 'Generate' button and save under the default file name.

  49. After generating the Netlist file, click on the 'Run Cvpcb' icon cvpcb_png on the top toolbar. If a missing file error window pops up, just ignore it and click OK.

  50. Cvpcb allows you to link all the components in your schematic with footprints in the KiCad library. The pane on the center shows all the components used in your schematic. Here select 'D1'. In the pane on the right you have all the available footprints, here scroll down to 'LEDs:LED-5MM' and double click on it.

  51. It is possible that the pane on the right shows only a selected subgroup of available footprints. This is because KiCad is trying to suggest to you a subset of suitable footprints. Click on the icons module_filtered_list_png, module_pin_filtered_list_png and module_library_list_png to enable or disable these filters.

  52. For 'IC1' select the 'Housings_DIP:DIP-8_W7.62mm' footprint. For 'J1' select the 'Connect:Banana_Jack_3Pin' footprint. For 'R1' and 'R2' select the 'Discret:R1' footprint.

  53. If you are interested in knowing what the footprint you are choosing looks like, you have two options. You can click on the 'View selected footprint' icon show_footprint_png for a preview of the current footprint. Alternatively, click on the 'Display footprint list documentation' icon datasheet_png and you will get a multi-page PDF document with all available footprints. You can print it out and check your components to make sure that the dimensions match.

  54. You are done. You can now update your netlist file with all the associated footprints. Click on FileSave As. The default name 'tutorial1.net' is fine, click save. Otherwise you can use the icon Save icon. Your netlist file has now been updated with all the footprints. Note that if you are missing the footprint of any device, you will need to make your own footprints. This will be explained in a later section of this document.

  55. You can close Cvpcb and go back to the Eeschema schematic editor. Save the project by clicking on FileSave Whole Schematic Project. Close the schematic editor.

  56. Switch to the KiCad project manager.

  57. The netlist file describes all components and their respective pin connections. The netlist file is actually a text file that you can easily inspect, edit or script.

    Library files (*.lib) are text files too and they are also easily editable or scriptable.
  58. To create a Bill Of Materials (BOM), go to the Eeschema schematic editor and click on the 'Bill of materials' icon bom_png on the top toolbar. By default there is no plugin active. You add one, by clicking on Add Plugin button. Select the *.xsl file you want to use, in this case, we select bom2csv.xsl.

    The *.xsl file is located in plugins directory of the KiCad installation, which is located at: /usr/lib/kicad/plugins/.

    Or get the file via:

    wget https://raw.githubusercontent.com/KiCad/kicad-source-mirror/master/eeschema/plugins/bom2csv.xsl
    KiCad automatically generates the command, for example:
    xsltproc -o "%O" "/home/<user>/kicad/eeschema/plugins/bom2csv.xsl" "%I"
    You may want to add the extension, so change this command line to:
    xsltproc -o "%O.csv" "/home/<user>/kicad/eeschema/plugins/bom2csv.xsl" "%I"

    Press Help button for more info.

  59. Now press 'Generate'. The file (same name as your project) is located in your project folder. Open the *.csv file with LibreOffice Calc or Excel. An import window will appear, press OK.

You are now ready to move to the PCB layout part, which is presented in the next section. However, before moving on let’s take a quick look at how to connect component pins using a bus line.

Bus connections in KiCad

Sometimes you might need to connect several sequential pins of component A with some other sequential pins of component B. In this case you have two options: the labelling method we already saw or the use of a bus connection. Let’s see how to do it.

  1. Let us suppose that you have three 4-pin connectors that you want to connect together pin to pin. Use the label option (press the l key) to label pin 4 of the P4 part. Name this label 'a1'. Now let’s press the Ins key to have the same item automatically added on the pin below pin 4 (PIN 3). Notice how the label is automatically renamed 'a2'.

  2. Press the Ins Key two more times. The Ins key corresponds to the action 'Repeat last item' and it is an infinitely useful command that can make your life a lot easier.

  3. Repeat the same labelling action on the two other connectors CONN_2 and CONN_3 and you are done. If you proceed and make a PCB you will see that the three connectors are connected to each other. Figure 2 shows the result of what we described. For aesthetic purposes it is also possible to add a series of 'Place wire to bus entry' using the icon Place wire to bus entry and bus line using the icon Place bus to bus entry, as shown in Figure 3. Mind, however, that there will be no effect on the PCB.

  4. It should be pointed out that the short wire attached to the pins in Figure 2 is not strictly necessary. In fact, the labels could have been applied directly to the pins.

  5. Let’s take it one step further and suppose that you have a fourth connector named CONN_4 and, for whatever reason, its labelling happens to be a little different (b1, b2, b3, b4). Now we want to connect Bus a with Bus b in a pin to pin manner. We want to do that without using pin labelling (which is also possible) but by instead using labelling on the bus line, with one label per bus.

  6. Connect and label CONN_4 using the labelling method explained before. Name the pins b1, b2, b3 and b4. Connect the pin to a series of 'Wire to bus entry' using the icon add_line2bus_png and to a bus line using the icon add_bus_png. See Figure 4.

  7. Put a label (press the l key option) on the bus of CONN_4 and name it 'b[1..4]'.

  8. Put a label (press the l key option) on the previous a bus and name it 'a[1..4]'.

  9. What we can now do is connect bus a[1..4] with bus b[1..4] using a bus line with the button add_bus_png.

  10. By connecting the two buses together, pin a1 will be automatically connected to pin b1, a2 will be connected to b2 and so on. Figure 4 shows what the final result looks like.

    The 'Repeat last item' option accessible via the Ins key can be successfully used to repeat period item insertions. For instance, the short wires connected to all pins in Figure 2, Figure 3 and Figure 4 have been placed with this option.
  11. The 'Repeat last item' option accessible via the Ins key has also been extensively used to place the many series of 'Wire to bus entry' using the icon add_line2bus_png.

    gsik_bus_connection_png

Layout printed circuit boards

It is now time to use the netlist file you generated to lay out the PCB. This is done with the Pcbnew tool.

Using Pcbnew

  1. From the KiCad project manager, click on the 'Pcbnew' icon pcbnew_png. The 'Pcbnew' window will open. If you get an error message saying that a *.kicad_pcb file does not exist and asks if you want to create it, just click Yes.

  2. Begin by entering some schematic information. Click on the 'Page settings' icon sheetset_png on the top toolbar. Set 'paper size' as 'A4' and 'title' as 'Tutorial1'.

  3. It is a good idea to start by setting the clearance and the minimum track width to those required by your PCB manufacturer. In general you can set the clearance to '0.25' and the minimum track width to '0.25'. Click on the Design RulesDesign Rules menu. If it does not show already, click on the 'Net Classes Editor' tab. Change the 'Clearance' field at the top of the window to '0.25' and the 'Track Width' field to '0.25' as shown below. Measurements here are in mm.

    Design Rules Window
  4. Click on the 'Global Design Rules' tab and set 'Min track width' to 0.25'. Click the OK button to commit your changes and close the Design Rules Editor window.

  5. Now we will import the netlist file. Click on the 'Read Netlist' icon netlist_png on the top toolbar. Click on the 'Browse Netlist Files' button, select 'tutorial1.net' in the File selection dialogue, and click on 'Read Current Netlist'. Then click the 'Close' button.

  6. All components should now be visible in the top left hand corner just above the page. Scroll up if you cannot see them.

  7. Select all components with the mouse and move them to the middle of the board. If necessary you can zoom in and out while you move the components.

  8. All components are connected via a thin group of wires called ratsnest. Make sure that the 'Hide board ratsnest' button general_ratsnest_png is pressed. In this way you can see the ratsnest linking all components.

    The tool-tip is backwards; pressing this button actually displays the ratsnest.
  9. You can move each component by hovering over it and pressing the g key. Click where you want to place them. Move all components around until you minimise the number of wire crossovers.

    If instead of grabbing the components (with the g key ) you move them around using the m key you will later note that you lose the track connection (the same occurs in the schematic editor). Bottom line, always use the g key option.
    gsik_tutorial1_080_png
  10. If the ratsnest disappears or the screen gets messy, right click and click 'Redraw view'. Note how one pin of the 100 ohm resistor is connected to pin 6 of the PIC component. This is the result of the labelling method used to connect pins. Labels are often preferred to actual wires because they make the schematic much less messy.

  11. Now we will define the edge of the PCB. Select 'Edge.Cuts' from the drop-down menu in the top toolbar. Click on the 'Add graphic line or polygon' icon add_dashed_line_png on the right toolbar. Trace around the edge of the board, clicking at each corner, and remember to leave a small gap between the edge of the green and the edge of the PCB.

  12. Next, connect up all the wires except GND. In fact, we will connect all GND connections in one go using a ground plane placed on the bottom copper (called B.Cu) of the board.

  13. Now we must choose which copper layer we want to work on. Select 'F.Cu (PgUp)' in the drop-down menu on the top toolbar. This is the front top copper layer.

    Select the Front top copper layer
  14. If you decide, for instance, to do a 4 layer PCB instead, go to Design RulesLayers Setup and change 'Copper Layers' to 4. In the 'Layers' table you can name layers and decide what they can be used for. Notice that there are very useful presets that can be selected via the 'Preset Layer Groupings' menu.

  15. Click on the 'Add Tracks and vias' icon add_tracks_png on the right toolbar. Click on pin 1 of 'J1' and run a track to pad 'R2'. Double-click to set the point where the track will end. The width of this track will be the default 0.250 mm. You can change the track width from the drop-down menu in the top toolbar. Mind that by default you have only one track width available.

    pcbnew_select_track_width_png
  16. If you would like to add more track widths go to: Design RulesDesign RulesGlobal Design Rules tab and at the bottom right of this window add any other width you would like to have available. You can then choose the widths of the track from the drop-down menu while you lay out your board. See the example below (inches).

    custom_tracks_width_png
  17. Alternatively, you can add a Net Class in which you specify a set of options. Go to Design RulesDesign RulesNet Classes Editor and add a new class called 'power'. Change the track width from 8 mil (indicated as 0.0080) to 24 mil (indicated as 0.0240). Next, add everything but ground to the 'power' class (select 'default' at left and 'power' at right and use the arrows).

  18. If you want to change the grid size, Right clickGrid Select. Be sure to select the appropriate grid size before or after laying down the components and connecting them together with tracks.

  19. Repeat this process until all wires, except pin 3 of J1, are connected. Your board should look like the example below.

    gsik_tutorial1_090_png
  20. Let’s now run a track on the other copper side of the PCB. Select 'B.Cu' in the drop-down menu on the top toolbar. Click on the 'Add tracks and vias' icon add_tracks_png. Draw a track between pin 3 of J1 and pin 8 of U1. This is actually not necessary since we could do this with the ground plane. Notice how the colour of the track has changed.

  21. Go from pin A to pin B by changing layer. It is possible to change the copper plane while you are running a track by placing a via. While you are running a track on the upper copper plane, right click and select 'Place Via' or simply press the v key. This will take you to the bottom layer where you can complete your track.

    place_a_via_png
  22. When you want to inspect a particular connection you can click on the 'Net highlight' icon net_highlight_png on the right toolbar. Click on pin 3 of J1. The track itself and all pads connected to it should become highlighted.

  23. Now we will make a ground plane that will be connected to all GND pins. Click on the 'Add Zones' icon add_zone_png on the right toolbar. We are going to trace a rectangle around the board, so click where you want one of the corners to be. In the dialogue that appears, set 'Pad in Zone' to 'Thermal relief' and 'Zone edges orient' to 'H,V' and click OK.

  24. Trace around the outline of the board by clicking each corner in rotation. Double-click to finish your rectangle. Right click inside the area you have just traced. Click on 'Fill or Refill All Zones'. The board should fill in with green and look something like this:

    gsik_tutorial1_100_png
  25. Run the design rules checker by clicking on the 'Perform Design Rules Check' icon drc_png on the top toolbar. Click on 'Start DRC'. There should be no errors. Click on 'List Unconnected'. There should be no unconnected track. Click OK to close the DRC Control dialogue.

  26. Save your file by clicking on FileSave. To admire your board in 3D, click on View3D Viewer.

    pcbnew_3d_viewer_png
  27. You can drag your mouse around to rotate the PCB.

  28. Your board is complete. To send it off to a manufacturer you will need to generate all Gerber files.

Generate Gerber files

Once your PCB is complete, you can generate Gerber files for each layer and send them to your favourite PCB manufacturer, who will make the board for you.

  1. From KiCad, open the Pcbnew software tool and load your board file by clicking on the icon open_document_png.

  2. Click on FilePlot. Select 'Gerber' as the 'Plot Format' and select the folder in which to put all Gerber files. Proceed by clicking on the 'Plot' button.

  3. These are the layers you need to select for making a typical 2-layer PCB:

Layer KiCad Layer Name Old KiCad Layer Name Default Gerber Extension "Use Protel filename extensions" is enabled

Bottom Layer

B.Cu

Copper

.GBR

.GBL

Top Layer

F.Cu

Component

.GBR

.GTL

Top Overlay

F.SilkS

SilkS_Cmp

.GBR

.GTO

Bottom Solder Resist

B.Mask

Mask_Cop

.GBR

.GBS

Top Solder Resist

F.Mask

Mask_Cmp

.GBR

.GTS

Edges

Edge.Cuts

Edges_Pcb

.GBR

.GM1

Using GerbView

  1. To view all your Gerber files go to the KiCad project manager and click on the 'GerbView' icon. On the drop-down menu select 'Layer 1'. Click on FileLoad Gerber file or click on the icon gerber_file_png. Load all generated Gerber files one at a time. Note how they all get displayed one on top of the other.

  2. Use the menu on the right to select/deselect which layer to show. Carefully inspect each layer before sending them for production.

  3. To generate the drill file, from Pcbnew go again to the FilePlot option. Default settings should be fine.

Automatically route with FreeRouter

Routing a board by hand is quick and fun, however, for a board with lots of components you might want to use an autorouter. Remember that you should first route critical traces by hand and then set the autorouter to do the boring bits. Its work will only account for the unrouted traces. The autorouter we will use here is FreeRouter from freerouting.net.

Freerouter is an open source java application, and it is needed to build by yourself to use with KiCad. Source code of Freerouter can be found on this site: https://github.com/nikropht/FreeRouting
  1. From Pcbnew click on FileExportSpecctra DSN or click on ToolsFreeRouteExport a Specctra Design (*.dsn) file and save the file locally. Launch FreeRouter and click on the 'Open Your Own Design' button, browse for the dsn file and load it.

    The ToolsFreeRoute dialog has a nice help button that opens a file viewer with a little document inside named Freerouter Guidelines. Please follow these guidelines to use FreeRoute effectively.
  2. FreeRouter has some features that KiCad does not currently have, both for manual routing and for automatic routing. FreeRouter operates in two main steps: first, routing the board and then optimising it. Full optimisation can take a long time, however you can stop it at any time need be.

  3. You can start the automatic routing by clicking on the 'Autorouter' button on the top bar. The bottom bar gives you information about the on-going routing process. If the 'Pass' count gets above 30, your board probably can not be autorouted with this router. Spread your components out more or rotate them better and try again. The goal in rotation and position of parts is to lower the number of crossed airlines in the ratsnest.

  4. Making a left-click on the mouse can stop the automatic routing and automatically start the optimisation process. Another left-click will stop the optimisation process. Unless you really need to stop, it is better to let FreeRouter finish its job.

  5. Click on the FileExport Specctra Session File menu and save the board file with the .ses extension. You do not really need to save the FreeRouter rules file.

  6. Back to Pcbnew. You can import your freshly routed board by clicking on the link ToolsFreeRoute and then on the icon 'Back Import the Spectra Session (.ses) File' and selecting your .ses file.

If there is any routed trace that you do not like, you can delete it and re-route it again, using the del key and the routing tool, which is the 'Add tracks' icon Add Track icon on the right toolbar.

Forward annotation in KiCad

Once you have completed your electronic schematic, the footprint assignment, the board layout and generated the Gerber files, you are ready to send everything to a PCB manufacturer so that your board can become reality.

Often, this linear work-flow turns out to be not so uni-directional. For instance, when you have to modify/extend a board for which you or others have already completed this work-flow, it is possible that you need to move components around, replace them with others, change footprints and much more. During this modification process, what you do not want to do is to re-route the whole board again from scratch. Instead, this is how you do it:

  1. Let’s suppose that you want to replace a hypothetical connector CON1 with CON2.

  2. You already have a completed schematic and a fully routed PCB.

  3. From KiCad, start Eeschema, make your modifications by deleting CON1 and adding CON2. Save your schematic project with the icon Save icon and c lick on the 'Netlist generation' icon netlist_png on the top toolbar.

  4. Click on 'Netlist' then on 'save'. Save to the default file name. You have to rewrite the old one.

  5. Now assign a footprint to CON2. Click on the 'Run Cvpcb' icon cvpcb on the top toolbar. Assign the footprint to the new device CON2. The rest of the components still have the previous footprints assigned to them. Close Cvpcb.

  6. Back in the schematic editor, save the project by clicking on 'File' → 'Save Whole Schematic Project'. Close the schematic editor.

  7. From the KiCad project manager, click on the 'Pcbnew' icon. The 'Pcbnew' window will open.

  8. The old, already routed, board should automatically open. Let’s import the new netlist file. Click on the 'Read Netlist' icon netlist_png on the top toolbar.

  9. Click on the 'Browse Netlist Files' button, select the netlist file in the file selection dialogue, and click on 'Read Current Netlist'. Then click the 'Close' button.

  10. At this point you should be able to see a layout with all previous components already routed. On the top left corner you should see all unrouted components, in our case the CON2. Select CON2 with the mouse. Move the component to the middle of the board.

  11. Place CON2 and route it. Once done, save and proceed with the Gerber file generation as usual.

The process described here can easily be repeated as many times as you need. Beside the Forward Annotation method described above, there is another method known as Backward Annotation. This method allows you to make modifications to your already routed PCB from Pcbnew and updates those modifications in your schematic and netlist file. The Backward Annotation method, however, is not that useful and is therefore not described here.

Make schematic components in KiCad

Sometimes a component that you want to place on your schematic is not in a KiCad library. This is quite normal and there is no reason to worry. In this section we will see how a new schematic component can be quickly created with KiCad. Nevertheless, remember that you can always find KiCad components on the Internet. For instance from here:

In KiCad, a component is a piece of text that starts with a 'DEF' and ends with 'ENDDEF'. One or more components are normally placed in a library file with the extension .lib. If you want to add components to a library file you can just use the cut and paste commands.

Using Component Library Editor

  1. We can use the Component Library Editor (part of Eeschema) to make new components. In our project folder 'tutorial1' let’s create a folder named 'library'. Inside we will put our new library file myLib.lib as soon as we have created our new component.

  2. Now we can start creating our new component. From KiCad, start Eeschema, click on the 'Library Editor' icon libedit_png and then click on the 'New component' icon new_component_png. The Component Properties window will appear. Name the new component 'MYCONN3', set the 'Default reference designator' as 'J', and the 'Number of parts per package' as '1'. Click OK. If the warning appears just click yes. At this point the component is only made of its labels. Let’s add some pins. Click on the 'Add Pins' icon pin_png on the right toolbar. To place the pin, left click in the centre of the part editor sheet just below the 'MYCONN3' label.

  3. In the Pin Properties window that appears, set the pin name to 'VCC', set the pin number to '1', and the 'Electrical type' to 'Passive' then click OK.

    Pin Properties
  4. Place the pin by clicking on the location you would like it to go, right below the 'MYCONN3' label.

  5. Repeat the place-pin steps, this time 'Pin name' should be 'INPUT', 'Pin number' should be '2', and 'Electrical Type' should be 'Passive'.

  6. Repeat the place-pin steps, this time 'Pin name' should be 'GND', 'Pin number' should be '3', and 'Electrical Type' should be 'Passive'. Arrange the pins one on top of the other. The component label 'MYCONN3' should be in the centre of the page (where the blue lines cross).

  7. Next, draw the contour of the component. Click on the 'Add rectangle' icon add_rectangle_png. We want to draw a rectangle next to the pins, as shown below. To do this, click where you want the top left corner of the rectangle to be (do not hold the mouse button down). Click again where you want the bottom right corner of the rectangle to be.

    gsik_myconn3_l_png
  8. If you want to fill the rectangle with yellow, set the fill colour to 'yellow 4' in PreferencesSelect color scheme, then select the rectangle in the editing screen and edit (E), selecting 'Fill background'.

  9. Save the component in your library myLib.lib. Click on the 'New Library' icon new_library_png, navigate into tutorial1/library/ folder and save the new library file with the name myLib.lib.

  10. Go to PreferencesComponent Libraries and add both tutorial1/library/ in 'User defined search path' and myLib.lib in 'Component library files'.

  11. Click on the 'Select working library' icon library_png. In the Select Library window click on myLib and click OK. Notice how the heading of the window indicates the library currently in use, which now should be myLib.

  12. Click on the 'Update current component in current library' icon save_part_in_mem_png in the top toolbar. Save all changes by clicking on the 'Save current loaded library on disk' icon save_library_png in the top toolbar. Click 'Yes' in any confirmation messages that appear. The new schematic component is now done and available in the library indicated in the window title bar.

  13. You can now close the Component library editor window. You will return to the schematic editor window. Your new component will now be available to you from the library myLib.

  14. You can make any library file.lib file available to you by adding it to the library path. From Eeschema, go to PreferencesLibrary and add both the path to it in 'User defined search path' and file.lib in 'Component library files'.

Export, import and modify library components

Instead of creating a library component from scratch it is sometimes easier to start from one already made and modify it. In this section we will see how to export a component from the KiCad standard library 'device' to your own library myOwnLib.lib and then modify it.

  1. From KiCad, start Eeschema, click on the 'Library Editor' icon libedit_png, click on the 'Select working library' icon library_png and choose the library 'device'. Click on 'Load component to edit from the current lib' icon import_cmp_from_lib_png and import the 'RELAY_2RT'.

  2. Click on the 'Export component' icon export_png, navigate into the library/ folder and save the new library file with the name myOwnLib.lib.

  3. You can make this component and the whole library myOwnLib.lib available to you by adding it to the library path. From Eeschema, go to PreferencesComponent Libraries and add both library/ in 'User defined search path' and myOwnLib.lib in the 'Component library files'. Close the window.

  4. Click on the 'Select working library' icon library_png. In the Select Library window click on myOwnLib and click OK. Notice how the heading of the window indicates the library currently in use, it should be myOwnLib.

  5. Click on the 'Load component to edit from the current lib' icon import_cmp_from_lib_png and import the 'RELAY_2RT'.

  6. You can now modify the component as you like. Hover over the label 'RELAY_2RT', press the e key and rename it 'MY_RELAY_2RT'.

  7. Click on 'Update current component in current library' icon save_part_in_mem_png in the top toolbar. Save all changes by clicking on the 'Save current loaded library on disk' icon save_library_png in the top toolbar.

Make schematic components with quicklib

This section presents an alternative way of creating the schematic component for MYCONN3 (see MYCONN3 above) using the Internet tool quicklib.

  1. Head to the quicklib web page: http://kicad.rohrbacher.net/quicklib.php

  2. Fill out the page with the following information: Component name: MYCONN3 Reference Prefix: J Pin Layout Style: SIL Pin Count, N: 3

  3. Click on the 'Assign Pins' icon. Fill out the page with the following information: Pin 1: VCC Pin 2: input Pin 3: GND. Type : Passive for all 3 pins.

  4. Click on the icon 'Preview it' and, if you are satisfied, click on the 'Build Library Component'. Download the file and rename it tutorial1/library/myQuickLib.lib.. You are done!

  5. Have a look at it using KiCad. From the KiCad project manager, start Eeschema, click on the 'Library Editor' icon libedit_png, click on the 'Import Component' icon import_png, navigate to tutorial1/library/ and select myQuickLib.lib.

    gsik_myconn3_quicklib_png
  6. You can make this component and the whole library myQuickLib.lib available to you by adding it to the KiCad library path. From Eeschema, go to PreferencesComponent Libraries and add library in 'User defined search path' and myQuickLib.lib in 'Component library files'.

As you might guess, this method of creating library components can be quite effective when you want to create components with a large pin count.

Make a high pin count schematic component

In the section titled Make Schematic Components in quicklib we saw how to make a schematic component using the quicklib web-based tool. However, you will occasionally find that you need to create a schematic component with a high number of pins (some hundreds of pins). In KiCad, this is not a very complicated task.

  1. Suppose that you want to create a schematic component for a device with 50 pins. It is common practise to draw it using multiple low pin-count drawings, for example two drawings with 25 pins each. This component representation allows for easy pin connection.

  2. The best way to create our component is to use quicklib to generate two 25-pin components separately, re-number their pins using a Python script and finally merge the two by using copy and paste to make them into one single DEF and ENDDEF component.

  3. You will find an example of a simple Python script below that can be used in conjunction with an in.txt file and an out.txt file to re-number the line: X PIN1 1 -750 600 300 R 50 50 1 1 I into X PIN26 26 -750 600 300 R 50 50 1 1 I this is done for all lines in the file in.txt.

Simple script
#!/usr/bin/env python
''' simple script to manipulate KiCad component pins numbering'''
import sys, re
try:
    fin=open(sys.argv[1],'r')
    fout=open(sys.argv[2],'w')
except:
    print "oh, wrong use of this app, try:", sys.argv[0], "in.txt out.txt"
    sys.exit()
for ln in fin.readlines():
    obj=re.search("(X PIN)(\d*)(\s)(\d*)(\s.*)",ln)
if obj:
    num = int(obj.group(2))+25
    ln=obj.group(1) + str(num) + obj.group(3) + str(num) + obj.group(5) +'\n'
    fout.write(ln)
fin.close(); fout.close()
#
# for more info about regular expression syntax and KiCad component generation:
# http://gskinner.com/RegExr/
# http://kicad.rohrbacher.net/quicklib.php
  1. While merging the two components into one, it is necessary to use the Library Editor from Eeschema to move the first component so that the second does not end up on top of it. Below you will find the final .lib file and its representation in Eeschema.

Contents of a *.lib file
EESchema-LIBRARY Version 2.3
#encoding utf-8
# COMP
DEF COMP U 0 40 Y Y 1 F N
F0 "U" -1800 -100 50 H V C CNN
F1 "COMP" -1800 100 50 H V C CNN
DRAW
S -2250 -800 -1350 800 0 0 0 N
S -450 -800 450 800 0 0 0 N
X PIN1 1 -2550 600 300 R 50 50 1 1 I

...

X PIN49 49 750 -500 300 L 50 50 1 1 I
ENDDRAW
ENDDEF
#End Library
gsik_high_number_pins_png
  1. The Python script presented here is a very powerful tool for manipulating both pin numbers and pin labels. Mind, however, that all its power comes for the arcane and yet amazingly useful Regular Expression syntax: http://gskinner.com/RegExr/.

Make component footprints

Unlike other EDA software tools, which have one type of library that contains both the schematic symbol and the footprint variations, KiCad .lib files contain schematic symbols and .kicad_mod files contain footprints. Cvpcb is used to successfully map footprints to symbols.

As for .lib files, .kicad_mod library files are text files that can contain anything from one to several parts.

There is an extensive footprint library with KiCad, however on occasion you might find that the footprint you need is not in the KiCad library. Here are the steps for creating a new PCB footprint in KiCad:

Using Footprint Editor

  1. From the KiCad project manager start the Pcbnew tool. Click on the 'Open Footprint Editor' icon edit_module_png on the top toolbar. This will open the 'Footprint Editor'.

  2. We are going to save the new footprint 'MYCONN3' in the new footprint library 'myfootprint'. Create a new folder myfootprint.pretty in the tutorial1/ project folder. Click on the PreferencesFootprint Libraries Manager and press 'Append Library' button. In the table, enter "myfootprint" as Nickname, enter "${KIPRJMOD}/myfootprint.pretty" as Library Path and enter "KiCad" as Plugin Type. Press OK to close the PCB Library Tables window. Click on the 'Select active library' icon library_png on the top toolbar. Select the 'myfootprint' library.

  3. Click on the 'New Footprint' icon new_footprint_png on the top toolbar. Type 'MYCONN3' as the 'footprint name'. In the middle of the screen the 'MYCONN3' label will appear. Under the label you can see the 'REF*' label. Right click on 'MYCONN3' and move it above 'REF*'. Right click on 'REF__*', select 'Edit Text' and rename it to 'SMD'. Set the 'Display' value to 'Invisible'.

  4. Select the 'Add Pads' icon pad_png on the right toolbar. Click on the working sheet to place the pad. Right click on the new pad and click 'Edit Pad'. You can otherwise use the e key shortcut.

    Pad Properties
  5. Set the 'Pad Num' to '1', 'Pad Shape' to 'Rect', 'Pad Type' to 'SMD', 'Shape Size X' to '0.4', and 'Shape Size Y' to '0.8'. Click OK. Click on 'Add Pads' again and place two more pads.

  6. If you want to change the grid size, Right clickGrid Select. Be sure to select the appropriate grid size before laying down the components.

  7. Move the 'MYCONN3' label and the 'SMD' label out of the way so that it looks like the image shown above.

  8. When placing pads it is often necessary to measure relative distances. Place the cursor where you want the relative coordinate point (0,0) to be and press the space bar. While moving the cursor around, you will see a relative indication of the position of the cursor at the bottom of the page. Press the space bar at any time to set the new origin.

  9. Now add a footprint contour. Click on the 'Add graphic line or polygon' button add_polygon_png in the right toolbar. Draw an outline of the connector around the component.

  10. Click on the 'Save Footprint in Active Library' icon save_library_png on the top toolbar, using the default name MYCONN3.

Note about portability of KiCad project files

What files do you need to send to someone so that they can fully load and use your KiCad project?

When you have a KiCad project to share with somebody, it is important that the schematic file .sch, the board file .kicad_pcb, the project file .pro and the netlist file .net, are sent together with both the schematic parts file .lib and the footprints file .kicad_mod. Only this way will people have total freedom to modify the schematic and the board.

With KiCad schematics, people need the .lib files that contain the symbols. Those library files need to be loaded in the Eeschema preferences. On the other hand, with boards (.kicad_pcb files), footprints can be stored inside the .kicad_pcb file. You can send someone a .kicad_pcb file and nothing else, and they would still be able to look at and edit the board. However, when they want to load components from a netlist, the footprint libraries (.kicad_mod files) need to be present and loaded in the Pcbnew preferences just as for schematics. Also, it is necessary to load the .kicad_mod files in the preferences of Pcbnew in order for those footprints to show up in Cvpcb.

If someone sends you a .kicad_pcb file with footprints you would like to use in another board, you can open the Footprint Editor, load a footprint from the current board, and save or export it into another footprint library. You can also export all the footprints from a .kicad_pcb file at once via PcbnewFileArchiveFootprintsCreate footprint archive, which will create a new .kicad_mod file with all the board’s footprints.

Bottom line, if the PCB is the only thing you want to distribute, then the board file .kicad_pcb is enough. However, if you want to give people the full ability to use and modify your schematic, its components and the PCB, it is highly recommended that you zip and send the following project directory:

tutorial1/
|-- tutorial1.pro
|-- tutorial1.sch
|-- tutorial1.kicad_pcb
|-- tutorial1.net
|-- library/
|   |-- myLib.lib
|   |-- myOwnLib.lib
|   \-- myQuickLib.lib
|
|-- myfootprint.pretty/
|   \-- MYCONN3.kicad_mod
|
\-- gerber/
    |-- ...
    \-- ...

More about KiCad documentation

This has been a quick guide on most of the features in KiCad. For more detailed instructions consult the help files which you can access through each KiCad module. Click on HelpManual.

KiCad comes with a pretty good set of multi-language manuals for all its four software components.

The English version of all KiCad manuals are distributed with KiCad.

In addition to its manuals, KiCad is distributed with this tutorial, which has been translated into other languages. All the different versions of this tutorial are distributed free of charge with all recent versions of KiCad. This tutorial as well as the manuals should be packaged with your version of KiCad on your given platform.

For example, on Linux the typical locations are in the following directories, depending on your exact distribution:

/usr/share/doc/kicad/help/en/
/usr/local/share/doc/kicad/help/en

On Windows it is in:

<installation directory>/share/doc/kicad/help/en

On OS X:

/Library/Application Support/kicad/help/en

KiCad documentation on the Web

Latest KiCad documentations are available in multiple languages on the Web.